B-made 3D printing
B-made enables Bartlett student access to desktop 3D printers across both sites. B-made also runs a 3D printing service open to the wider UCL community and industry professionals.
On this page:
B-made's 3D printing options
B-made's 3D offers pay-for-print services for our industrial grade machines, B-made also enable Bartlett students to access and operate desktop 3D printers located throughout our buildings. Find out more below.
Desktop 3D printers (bookable by Bartlett students only)
Bartlett Students only. If you are from a different faculty please check out information on the pay for-print service.
Students who have completed the B-made Baseline induction (hosted on Moodle) will have access to a booking system. Students can select a timeslot to use one of the printers.
- material: 2.85mm PLA filament
- build size X Y Z: 223mm x 223 x 205
- file transfer: SD card
- software: Ultimaker Cura
3D printing technologies (service run)
3D printing technologies
B-made offers advanced capabilty in 3D printing through its 3D printing services. Unlike other numerical manufacturing equipment in B-made, the machines listed below must be run by B-made technicians so are not available for students to use on their own.
Files from students, UCL researches and staff and other external industry professionals can be submitted to the 3D Printing department by Email:
The 3D printing team will review the data, advise and quote each request based on the technology used, size and geometry.
B-made has temporarily postponed any in-person (face to face) file submissions until further notice. Please contact us via the email above only.
Please note that the 3D printing team will respond to emails as soon as possible and are not available in the afternoons to ensure they can process the pay-for-print services.
Send files to the B-made 3D printing team:
3dp.bartlett@ucl.ac.uk
Learn more about our capability below:
SLS properties
- machine: EOS Formiga P100
- build size: 240mm x 190mm x 320mm
- material: PA 2200 (nylon powder)
- cost: calculated on bounding box
SLS advantages
- fine detail
- strong
- low cost when small
- flexible if thin
- good surface finish
- can print any geometry (no support material required)
SLS disadvantages
- 1 week lead time*
- white material only (can later be died or sprayed)
- large objects can warp
Polyjet properties
- machine: Stratasys J835
- build size: 350mm x 350mm x 200mm
- material: acrylic-based resin (rigidity 30 shore to 95 shore)
- cost: calculated by weight of material used
Polyjet advantages
- dual-material printing
- full colour prints: Pantone validated
- transparent or opaque
- glossy or matte surface finish*
- can mix materials: desireable flexibility
- rubber-like materials
- 24-hour lead time*
- soluable support material
Polyjet disadvantages
- can be expensive depending on geometry and size
- support material can be difficult to remove
- surfaces that require support material have a matte finish (underside)
SLA properties
- machine: Form labs – Form 3
- build size: 140mm x 140mmx 170mm
- material: 'clear' acrylic-based resin (rigid)
- cost: calculated by amount of material used
SLA advantages
- lower cost compared to Polyjet
- support structure enables hollow parts
- can be polished or sprayed for high transparency
SLA disadvantages
- can be brittle
- small build volume
- translucent only (can be sprayed)
- supports leave behind small spikes
FDM properties
- machine 1: Ultimaker 2+ (190mm x 190mm)
- machine 2: Prusa I3 mk2.5s (250mm x 200mm x 200mm)
- material: PLA (rigid) other materials upon request
- cost: calculated by machine running-time
FDM advantages
- large build volume
- low cost for size of model produced
FDM disadvantages
- slow
- poor surface finish
- support material can be difficult to remove
- a flat base will warp
- units are set to mm
- model is the correct scale/size
- model is moved to origin location
- all objects are closed solids
- minimum thickness 1mm +
- export as STL file
- single surfaces
- missing surfaces
- duplicated geometry (overlapping)
- open edges
- files over 200mb
- self-intersecting geometry
- floating elements (not attached)
- geometry located away from the origin
- non-manifold edges
Material Advice
The material selected for each 3D print will vary depending on what is required of the model and its geometry. When we review your data and design we will be able to advise you on the most appropriate technology and material to use. Alternatively, if you know what material finish you require, we can give design guidelines to optimise the geometry to suit the process.
- colour/transparency
- surface finish
- level of detail
- cost
- strength/functional properties
- lead time
- post processing option
- support structure/material
Submit files for printing
Please email your print request to 3dp.bartlett@ucl.ac.uk
Students and staff based on-site are encouraged to visit us in person at the Bartlett School of Architecture, 22 Gordon Street before submitting files.
Ensure 3D files have:
- units in millimetres
- model moved to the origin
- accounted for 0.1mm of tolerance
- a water tight model (no single surfaces or naked edges)
- been saved as STL
- been saved as a file less than 100MB
B-made 3D printing location
The Bartlett School of Architecture
B-made workshop, Room B.10 (Basement), 22 Gordon Street, London, WC1H 0QB
Contacts
All 3D print enquiries: 3dp.bartlett@ucl.ac.uk
- Martyn Carter, 3D Printing Manager
Tel. 02035495706
martyn.carter@ucl.ac.uk - Sienna Griffin-Shaw, 3D Printing Technician
s.griffin-shaw@ucl.ac.uk